|
Kia Sportage>> Systems of electric equipment of the engine
Systems of electric equipment of the engine Specifications
|
Separate characteristics are provided also in the text of head and in case of obligation of their performance are allocated with a bold print. |
System of ignition of the petrol engine
Type |
Electronic system of direct ignition (DIS) with the single spark, functioning under control of ECM which is guided by indications of sensors of provisions of cranked (CKP) and distributive (CMP) of shaft |
Installation of a corner of an advancing of ignition |
4 ° ± 2 ° before VMT (under control of ECM, to adjustment is not subject) |
Ignition order |
1-3-4-2 |
Ignition coils |
|
Two dual bobbin modules (on one on two cylinders) |
Coil supply voltage (taking into account a ballast), In
|
12.0 |
Resistance of primary winding, Ohm
|
0.45 ÷ 0.55 |
Resistance of a secondary winding, kiloohm
|
13 ÷ 15 |
Wire VV |
Specific resistance, kiloohm/m
|
16 |
Spark plugs |
|
|
BKR6E-11 |
|
FR7DCX |
|
RC7YC4 |
|
14FR-7DUX |
|
APP3923 |
Interelectrode gap (all producers), mm |
1.1 |
System of simplification of cold start of the diesel engine
Charge system
Storage battery |
Electrolit density at 25°С (all models), kg/dm3
|
|
1.280 |
Limiting admissible difference between banks
|
0.04 |
Rated target voltage, In (grounding on a negative pole)
|
12 |
The capacitor characteristic (at the rate on 5 hours), Ach
|
|
60 |
|
68 |
Generator |
|
Alternating current |
Target characteristic, V-and
|
|
12.-70 |
|
12-60 |
Regulator type (all models)
|
Transistor, it is built in the bobbin module |
Nominal frequency of rotation, rpm
|
|
Data are absent |
|
5000 |
Working range of turns, mines-1
|
|
Data are absent |
|
1000 ÷ 11000 |
|
|
Data are absent |
|
12 |
Vacuum pump (diesel models) |
Depth of depression, mm of mercury.
|
At frequency of rotation of the generator of 1500 rpm, 20 seconds later
|
Not less than 440 |
At frequency of rotation of the generator of 3000 rpm, 20 seconds later
|
Not less than 580 |
Length of shiberny shovels, mm
|
13.0 ÷ 13.5 |
Internal diameter of a casing, mm
|
57.0 ÷ 57.1 |
Start system
Type of a drive of a cranked shaft |
|
|
|
Bezreduktorny |
|
Reduktorny |
|
Bezreduktorny |
The maximum current at an engine provorachivaniye, And |
|
130 ÷ 158 |
|
Data are absent |
Starter |
|
|
|
0.9 |
|
1.2 |
|
2.0 |
|
|
|
17 |
|
18 |
Limiting admissible value
|
|
11.5 |
|
11 |
Effort developed by a shchetochny spring (all models), N |
8.8 |
Size of palpation of anchor assembly (all models) |
|
|
0.05 |
Limiting admissible value
|
0.4 |
Collector pro-point (all models) |
|
Minimum admissible diameter, mm
|
31 |
Depth of a notch, mm |
|
|
0.02 ÷ 0.03 |
Limiting admissible value
|
0.2 |
Working gap of a gear wheel (petrol models), mm
|
0.5 |
Axial люфт gear wheels (diesel models) |
Working gap of a gear wheel of a starter (petrol models)
Efforts of a tightening of carving connections, Nanometer
|
Efforts of a tightening of separate elements of fixture can be brought directly in the text of sections where they are allocated with a bold print. |
Petrol models
Bolts of fastening of bobbin assemblies |
19 ÷ 25 |
Spark plugs |
25 ÷ 30 |
Bolts of fastening of a starter and its basic arm |
37 ÷ 54 |
Nut of the plug B of a starter |
16 ÷ 23 |
Bolts of fastening of the inlet pipeline |
37 ÷ 54 |
Axial and fixing bolts of the generator |
38 ÷ 51 |
Screws of a bearing casing of the generator |
2.0 ÷ 5.4 |
Bolts of a cover of the generator |
2.0 ÷ 5.4 |
Nut of fastening of a pulley of a drive of the generator |
59 ÷ 98 |
Screws of fastening of diode assembly of the rectifier |
2.0 ÷ 5.4 |
Bolt of a support of a natyazhitel |
19 ÷ 26 |
Diesel models
Glow plugs |
14.7 ÷ 19.6 |
Bolts of fastening of a starter and its basic arm |
37 ÷ 54 |
Nut of the plug B of a starter |
16 ÷ 23 |
Bolts of fastening of the generator (see an illustration) |
|
19 ÷ 26 |
|
38 ÷ 51 |
|
|