KIA of Sportazh - Kia Sportage
Governing bodies and operation receptions
Current leaving and service
Engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases
Systems of electric equipment of the engine
Five-step manual box of gear shifting
Automatic transmission
Transmission line
   General information
   Coupling
   Transfer case
   Driveshafts
      General information
      Condition check without removal from the car
      Removal, service and installation of driveshafts
   Bridges
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control body sizes
Schemes of electric connections



Kia Sportage>> Transmission line>> Driveshafts>> Removal, service and installation of driveshafts

Removal, service and installation of driveshafts

Removal

Forward shaft

 PERFORMANCE ORDER

  1. Mark the adjusting provision of a shaft of rather connecting flange of a leading gear wheel of the main transfer of the forward bridge, release fixing bolts/nuts, release the forward end of a shaft and tie it to chassis/suspension bracket elements.
  1. Mark the adjusting provision of a shaft of rather connecting flange of a target shaft of a transfer case, release four fixing nuts, separate a shaft and take it from under the car.

Back shaft

 PERFORMANCE ORDER

  1. Mark the adjusting provision of a shaft of rather connecting flange of a target shaft of a transfer case, release four fixing bolts/nuts, separate the forward end of a shaft from a transfer case and tie up it to chassis elements.
  1. Mark the adjusting provision of a shaft of rather connecting flange of a leading gear wheel of the main transfer of the back bridge, release four fixing bolts/nuts, separate a shaft and take it from under the car.

Both shaft

 PERFORMANCE ORDER

  1. If there is a need for division of the sections of a shaft jointed by shlitsa, it is necessary to mark their adjusting situation previously in order to avoid balancing violation.

Service

 PERFORMANCE ORDER

  1. Carefully wipe components of assemblies of kardanny hinges.
  2. Clamp a shaft body in a vice with soft sponges.
  1. Mark the provision of components of the kardanny hinge from each other, - the wrong joint of components can lead to violation of balancing of assembly.
  1. Hooking a screw-driver with a flat sting, remove lock rings fixing sharnirny assembly.
  1. Easily tapping on a collar with a hammer with soft brisk, take crosspiece bearings. Remove a collar.
  1. By means of a suitable drift beat out bearings and remove a crosspiece.
  1. Estimate a condition of components, in case of need prepare replaceable knots.
  1. Before assembly fill in covers and rollers of bearings, and also in lubricant openings of a crosspiece greasing on a lithium basis (NGLI No. 2).
  1. Fill a crosspiece in a shaft fork, - track correctness of combination of the landing labels put in the course of dismantle, - and by means of a hammer with soft brisk begin to knock two bearings.
  1. Plant on a crosspiece a collar of the kardanny hinge, - track correctness of combination of the landing labels put in the course of dismantle, - and by means of a hammer with soft brisk begin to knock two bearings.
  1. Fix assembly by NEW lock rings, having tracked correctness of landing them in reception flutes.

Lock rings should be selected so that the starting effort of a provorachivaniye of the hinge did not fall outside the limits an admissible range (cm of the Specification of Head the Transmission line). All four rings should be one thickness.


  1. Check starting effort of a provorachivaniye of sharnirny assembly. Compare results of measurement to requirements of Specifications of Head the Transmission line, in case of need make the corresponding adjustment by selection of lock rings of other thickness (see the table).

detail No.

Thickness, mm

detail No.

Thickness, mm

1757 25 171 1.22 1757 25 176 1.32
1757 25 172 1.24 1757 25 177 1.34
1757 25 173 1.26 1757 25 178 1.36
1757 25 174 1.28 1757 25 179 1.38
1757 25 175 1.30

  1. Connect shaft sections, - track correctness of combination of landing labels, then lay a shaft in prisms and by means of a measuring instrument of plunzherny type define size of its bend. If the result of measurement exceeds limiting admissible value (see. Specifications of Head the Transmission line), will measure a shaft.

Installation

 PERFORMANCE ORDER

  1. Installation is made as it should be, the return to an order of dismantle of components, - track correctness of combination of landing labels and behind observance of requirements of Specifications of Head the Transmission line to efforts of a tightening of carving connections.