|
|
Kia Sportage>> Body>> External equipment and body elements>> Dismantling, removal, installation and adjustment of doors
Dismantling, removal, installation and adjustment of doors
Forward doors
Design of assembly of a forward door
Dismantling, removal and installation
|
|
Disconnect a negative wire from the battery.
Remove the panel of an internal upholstery of a door.
|
|
Turn out two fixing screws and remove an arm of the poruchnevy handle.
|
|
|
Turn out four fixing bolts, liberate from clamps on a doorframe a plait of electroconducting and the loudspeaker loudspeaker. Disunite the contact socket and remove the loudspeaker.
|
Separate from a door the film insulating screen.
Connect the battery and, - if disconnected, - electroconducting of the switch of a drive of a window regulator. Include ignition and half lower door glass. Switch off ignition and disconnect a negative wire from the battery.
Through an aperture in a doorframe turn out two bolts of fastening of glass to a window regulator regulator.
|
|
Having inclined forward, accurately take glass from a window doorway.
|
|
|
Disconnect electroconducting from the electromotor of a drive of a regulator of a window regulator, give six nuts and through a service opening take regulator assembly from a doorframe.
|
|
|
Remove directing trench (1) window aperture.
|
|
|
Turn out one fixing bolt and through a service opening take directing glasses from a doorframe.
|
|
|
Rotating counter-clockwise, remove the button of an otpuskaniye of the lock of a door.
|
Disconnect two driving rods from the external handle of a door.
|
|
Turn out three fixing bolts and through a service opening take from a doorframe zamkovy assembly.
|
On the right door give two fixing nuts and remove the lock activator.
Give two fixing nuts and remove the external handle of a door.
Remove a door rear-view mirror (see. Section Removal and installation of door rear-view mirrors).
Disunite five contact sockets of the electroconducting laid in a doorframe.
Through a service opening take electroconducting from a frame.
|
|
Accurately beat out a hammer a finger of the limiter of a course of a door, - try not to damage a paint and varnish covering.
|
Give two fixing nuts and remove the limiter.
Remove a boot of a door threshold.
|
|
Turn out four loopy bolts and remove a door from the car, - use the help of the assistant.
|
|
|
In case of need remove panels of furnish of a door threshold and the bottom section of a rack In and remove from an adjusting flange of a doorway a sealing strip.
|
Installation is made as it should be, the return to an order of dismantle of components, - track observance of requirements of Specifications of Head the Body to efforts of a tightening of carving fixture.
Check correctness of landing of a door in a body aperture, in case of need make the corresponding adjustment.
|
|
Adjustment
|
|
Release loopy bolts and level a door in an aperture of rather surrounding body panels. Having finished adjustment, do not forget to tighten bolts with demanded effort.
Check correctness of a zashchelkivaniye of the door lock. In case of need release fixing bolts and correct position of the drummer.
|
|
By removal of the drummer in the horizontal direction position of back edge of the closed door concerning a rack surface can be leveled. |
|
|
Back doors
The order of performance of procedures is similar described above for forward doors adjusted for differences in a design of assemblies.
Design of assembly of a back door
Back door
Design of assembly of a door of a back
Dismantling, removal and installation
|
|
Disconnect a negative wire from the battery.
Open a back door.
Turn out two fixing screws and uncover a door stoplight of the top level.
Disconnect electroconducting, turn out two fixing screws and remove a stoplight lamp.
Having disunited two contact sockets (on one from each party of door assembly) disconnect electroconducting of a heater of back glass.
Remove earthing uvula of fixing of the right socket of electroconducting of a heater.
Release 12 clamps and remove the bottom panel of an internal upholstery of a door.
Remove a plastic cover to the left of the central aperture in a doorframe and through a service opening disunite three contact sockets of internal electroconducting of a door.
Disunite three one-contact, located in the left top corner of door assembly.
Take from a landing opening in the left top corner of a door the rubber plug through passage and liberate from a doorframe an electroconducting plait.
Take pins from the socket of a stoplight and one pin from the left socket of a heater of glass.
Accurately liberate electroconducting plaits from the cable channel in a doorframe, and also from a protective casing and the rubber plug through passage.
Fix cases of sockets the pins.
Liberate from a doorframe the right plug through passage, having provided with that access to a tube of supply of liquid to a nozzle of washing of back glass.
Remove a nozzle and disconnect from it submitting tube.
|
|
Having got of support of the assistant, reliably fix a back door in open situation and disconnect from a door spherical support of a telescopic emphasis.
|
For the purpose of simplification of procedure of installation compress a protective cover and fix from its outer side the socket of a submitting hose.
Disconnect submitting hose from the socket and remove it from the car.
|
|
Turn out on one loopy bolt.
|
Having made sure of reliability of fixing of a door, turn out the remained two bolts and remove door assembly from the car.
Installation is made as it should be, the return to an order of dismantle of components, - track observance of requirements of Specifications of Head the Body to efforts of a tightening of carving fixture.
Check correctness of landing of a door in a body aperture, in case of need make the corresponding adjustment.
|
|
Adjustment
|
|
|
|
Make control measurements And, In and D and make sure that results of measurement do not fall outside the limits admissible ranges, in case of need release loopy bolts and spherical support of a telescopic emphasis and correct the provision of a door in a body aperture. Having finished adjustment, tighten bolts and support with demanded effort.
|
|
|
Make control measurement With, - situation established on lateral stacks of a body aperture of wedges defines a corner of closing of a door on S.Esli's type result of measurement exceeds admissible value, shift wedges outside, - for increase in the size it is necessary to shift, on the contrary, wedges towards an aperture.
|
|
|
|
|