Kia Sportage>>
Body>>
Salon equipment
Salon equipment
The dashboard - the general information, removal and installation of components
General information
The dashboard is made of plastic and equipped with a metal strengthening frame. The panel consists of three main sections: left, central and right.
Dashboard design (the bottom cover is removed)
In the left section of the panel the combination of devices with a protective peak, and also some switches (is established see. The section Governing bodies and the salon equipment in Head Governing bodies and operation receptions). To the left of a steering column also assembly block of safety locks is located. From below, more to the left of a steering column the panel of a knee emphasis in which, at the corresponding complete set the module of a knee safety cushion is built in also is established.
The structure of the central section includes the control panel functioning of systems of heating/ventilation/air conditioning, a radio receiver, the lighter and a forward ashtray.
In the right section there is a ware box and, at the corresponding complete set, - a passenger safety cushion.
Removal and installation of components
|
Disconnect a negative wire from the battery.
|
|
Furnish panel
|
Disconnect the corresponding electroconducting and remove the console panel.
|
Turn out fixing screws and remove the finishing panel, - do not forget to disconnect electroconducting from the corresponding switches.
|
Installation is made upside-down.
|
|
Combination of devices
|
Remove the finishing panel.
|
Turn out four fixing screws and liberate a combination from the dashboard.
|
Disconnect electroconducting from measuring instruments and remove a combination of devices.
Installation is made upside-down.
|
|
Knee emphasis
|
Turn out fixing screws and remove a knee emphasis.
Installation is made upside-down.
|
|
Bottom cover
|
|
Turn out fixing screws and remove the bottom cover of the dashboard.
|
Installation is made upside-down.
|
|
Ware box
|
|
Turn out fixing screws and take assembly of a ware box from the dashboard.
|
Installation is made upside-down.
|
|
Handle of a drive of an otpuskaniye of a latch of the lock of a cowl
|
|
Turn out the fixing screw and remove the handle (1).
|
In case of need release a nut of fixing of a driving cable.
Installation is made upside-down.
|
|
Panels of furnish of forward racks
|
|
Hooking the suitable tool, remove panels of furnish of forward racks.
|
Installation is made upside-down, - track reliability of a zashchelkivaniye of clamps.
|
|
Left cover
|
Turn out fixing screws and remove the left cover of the dashboard.
Installation is made upside-down.
|
|
Right cover
|
Remove a ware box.
|
Turn out five fixing screws and remove the right cover of the dashboard.
|
Installation is made upside-down.
|
|
Radio receiver
|
Make sure that the battery is disconnected.
|
Turn out four fixing screws and liberate radio receiver assembly from the dashboard.
|
Disconnect electroconducting and an antenna cable and finally remove a radio receiver from the dashboard.
Installation is made upside-down.
|
|
Control panel functioning of systems of heating, ventilation and air conditioning
|
Make sure that the battery is disconnected.
Remove the furnish panel.
|
Turn out four fixing screws and liberate assembly of switches of management by functioning of systems of heating, ventilation and To/in from the dashboard.
|
Disconnect brought to a back part of the panel of switches electroconducting.
Remove a ware box.
Accurately releasing plastic clamps, disconnect from operating switches driving cables.
Finally remove assembly of operating switches.
Installation is made upside-down.
|
|
T-shaped frame
|
Remove a steering wheel (see. Head Suspension bracket and steering).
Remove the left cover of the dashboard.
|
Turn out two fixing screws, located at the left and on the right under a steering column and remove T-shaped, - the steering column should fall.
|
Installation is made upside-down.
|
|
Dashboard body
|
Remove a steering wheel (see. Head Suspension bracket and steering).
Remove back section of the central console (see. Section Removal and installation of the central console).
Remove forward section of the central console (see. Section Removal and installation of the central console).
Remove assembly of a knee emphasis.
Remove a steering wheel (see. Head Suspension bracket and steering).
Remove the basic arm of the assembly block of the relay located at the left under the dashboard.
Remove the handle of a drive of an otpuskaniye of a latch of the lock of a cowl.
Remove panels of furnish of forward racks.
Remove the left cover of the dashboard.
|
Turn out two fixing bolts at the left on T-shaped.....
|
|
Turn out three left bolts of fastening of a body of the dashboard.
|
Remove a forward ashtray.
Remove the furnish panel.
Remove the panel of switches of management of functioning of systems of heating, ventilation and К/В.
Remove a ware box.
Remove the right cover of the dashboard.
|
Remove a decorative cover and turn out the central fixing bolt.
|
|
Turn out two fixing bolts on the right on T-shaped.....
|
|
Turn out three right bolts of fastening of a body of the dashboard.
|
|
Turn out two fixing bolts on either side of a steering column and lower the last on level of a floor of the car.
|
|
Turn out two fixing bolts, located behind mentioned in the previous paragraph access to which opens after lowering of a steering column.
|
Disunite contact sockets of all procedure of electroconducting stirring to performance.
Remove a dashboard body.
Installation is made upside-down.
|
|