KIA of Sportazh - Kia Sportage
Governing bodies and operation receptions
Current leaving and service
Engine
   Check of kompressionny pressure, assessment of a condition of cylinders
   Engine check by means of the vacuum gage
   Belts of a drive of auxiliary units
   Petrol models
   Diesel models
      Greasing system - the general information
      Removal and engine installation
      Removal and installation of components of a drive of GRM
      Check and adjustment of klapanny gaps
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components of the gas-distributing mechanism
      Dismantling and assembly of the block of cylinders, service of components
      Removal and installation of the pallet of a case
      Removal, installation and service of the oil pump
      Removal and installation of a maslookhladitel
      Removal and flywheel installation
      Removal and installation of masloraspylitel
      Replacement of epiploons of a cranked shaft
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases
Systems of electric equipment of the engine
Five-step manual box of gear shifting
Automatic transmission
Transmission line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control body sizes
Schemes of electric connections



Kia Sportage>> Engine>> Diesel models>> Check and adjustment of klapanny gaps

Check and adjustment of klapanny gaps

This procedure is among those which performance does not demand removal of the engine from the car. Performance of procedure should be made on the cold engine.

Check

 PERFORMANCE ORDER

  1. Remove an intermediate cooler of system of pressurization of air (Intercooler) (see. Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases).
  2. Uncover heads of cylinders.
  3. Having turned a cranked shaft so that cams of a drive of inlet and final valves on distributive to a shaft were developed by working ledges up, bring the piston of the first cylinder into the provision VMT of the end of a step of compression.
1 — the Cam of a drive of the inlet valve
2 — the Cam of a drive of the final valve
  1. With the help щупа lezviyny type measure size of klapanny gaps, result write down.
  1. Turning a cranked shaft in the normal direction, repeat procedure for the remained valves, passing from the cylinder to the cylinder as ignition.
  2. Compare results of measurements to requirements of Specifications of Head the Engine, in case of need make the corresponding adjustment.

Adjustment

 PERFORMANCE ORDER

  1. Arrange a camshaft so that the cam of a drive of the inlet valve subject to adjustment appeared will develop a working ledge vertically up.
  2. For the purpose of simplification of access to an adjusting washer, develop a pusher of the valve risky towards the inlet pipeline.
  3. By means of the special adaptation wring out a pusher down and, having used a small screw-driver, or other suitable tool, take an adjusting washer.
Extraction of an adjusting washer.
1 — the Adjusting washer
2 — Pushers
3 — Inlet
4 — Final
  1. Having made necessary calculations, pick up a new adjusting washer of the demanded thickness, plant it in a pusher and repeat check.

At calculation of the demanded thickness of a new adjusting washer it is necessary to use the following formula:

Н1 = Н0 + (dM - dS)

Where:   

Н1 — Settlement thickness of a demanded washer

Н0 — Thickness of the removed washer

dM — Size of the measured gap

dS — Nominal size of a gap

For example:

Let:

Н0 = 4.00 mm, dM = 0.30 mm,

dS = 0.25 mm,

Example of collecting initial information at calculation of the demanded thickness of a new adjusting washer

1 — the Cam of a drive of the inlet valve
2 — the Adjusting washer
3 — Klapanny a gap

Then:

Н1 = 4.00 + (0.30 – 0.25) = 4.05 (mm)

In sale adjusting washers of three dimensional ranges arrive: 3.400 ÷ 3.650 mm and 4.350 ÷ 4.600 mm with a step of 0.050 mm and 3.700 ÷ 4.300 mm with a step of 0.025 mm (only 37 options). The thickness of a washer can be determined by code number beaten out on it: so, the washer with number 3825 has thickness of 3.825 mm.