The device and repair of Kia Sportage SUVs (KIA of Sportazh) - Removal and installation of components of a drive of GRM-//kupit-derevo.ru
KIA of Sportazh - Kia Sportage
Governing bodies and operation receptions
Current leaving and service
Engine
   Check of kompressionny pressure, assessment of a condition of cylinders
   Engine check by means of the vacuum gage
   Belts of a drive of auxiliary units
   Petrol models
   Diesel models
      Greasing system - the general information
      Removal and engine installation
      Removal and installation of components of a drive of GRM
      Check and adjustment of klapanny gaps
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components of the gas-distributing mechanism
      Dismantling and assembly of the block of cylinders, service of components
      Removal and installation of the pallet of a case
      Removal, installation and service of the oil pump
      Removal and installation of a maslookhladitel
      Removal and flywheel installation
      Removal and installation of masloraspylitel
      Replacement of epiploons of a cranked shaft
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases
Systems of electric equipment of the engine
Five-step manual box of gear shifting
Automatic transmission
Transmission line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control body sizes
Schemes of electric connections



Kia Sportage>> Engine>> Diesel models>> Removal and installation of components of a drive of GRM

Removal and installation of components of a drive of GRM

This procedure is among those which performance does not demand removal of the engine from the car.

Details of installation of components of a drive of GRM

1 — the Damper of krutilny fluctuations
2 — the Pulley of a cranked shaft
3 — the Right cover of a drive of GRM
4 — the Left cover of a drive of GRM
5 — the Cover of a head of cylinders
6 — the Tension roller with a spring
7 — the Gas-distributing belt

8 — the Cogwheel of a drive of TNVD
9 — Gear a wheel of a drive of a camshaft
10 — the Cogwheel of a cranked shaft
11 — the Thermostat
12 — the Basic arm of the fan of system of cooling
13 — the Sealing plate
14 — the Water pump with basic a generator lump


 PERFORMANCE ORDER

  1. Remove a belt of a drive of GRM (see. The section Check of a condition and replacement of a belt of a drive of GRM in Head the Current leaving and service).
  1. For the purpose of prevention of risk of input of valves in contact to pistons at removal of cogwheels develop a cranked shaft so that the adjusting label on its cogwheel was displaced under 45 ° relatively risks on the case of the oil pump.
  1. Release a bolt of fastening of a cogwheel of TNVD, - the wheel can be blocked from a provorachivaniye by a way of a prodevaniye to openings in its spokes of pair of bolts (М8 x 1.25 x 30 ÷ 40) with a vvorachivaniye of their ends in a carving opening in a basic arm of pump assembly.
  1. By means of a special stripper make dismantle of a cogwheel of TNVD.
  1. Uncover heads of cylinders and, holding a camshaft from a provorachivaniye for specially provided лыски, - try not to damage a key head molding, - turn out a fixing bolt and, operating in a manner similar described in paragraph 4, remove a cogwheel of a drive of GRM.
  1. By means of the special adaptation block from a povorachivaniye a flywheel / a driving disk (see an illustration) and remove a cogwheel from a cranked shaft.
  2. At installation of components into place track correctness of combination of adjusting labels (see. The section Check of a condition and replacement of a belt of a drive of GRM in Head the Current leaving and service). All fixture tighten with demanded effort.