KIA of Sportazh - Kia Sportage
Governing bodies and operation receptions
Current leaving and service
Engine
   Check of kompressionny pressure, assessment of a condition of cylinders
   Engine check by means of the vacuum gage
   Belts of a drive of auxiliary units
   Petrol models
      Greasing system - the general information, check of pressure of impellent oil
      Removal and engine installation
      Removal and installation of components of a drive of GRM
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components of the gas-distributing mechanism
      Dismantling and assembly of the block of cylinders, service of components
      Removal and installation of the pallet of a case
      Removal, installation and service of the oil pump
      Removal and flywheel installation / driving disk
      Removal and installation of masloraspylitel
      Replacement of epiploons of a cranked shaft
   Diesel models
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases
Systems of electric equipment of the engine
Five-step manual box of gear shifting
Automatic transmission
Transmission line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control body sizes
Schemes of electric connections



Kia Sportage>> Engine>> Petrol models>> Replacement of epiploons of a cranked shaft

Replacement of epiploons of a cranked shaft

This procedure is among those which performance does not demand removal of the engine from the car.

Forward epiploon

 PERFORMANCE ORDER

    Disconnect a negative wire from the battery. Turn out four fixing bolts and remove protection of a case of the engine. Merge impellent oil (see. Head Current leaving and service). Remove a belt of a drive of GRM (see. Head Current leaving and service). Turn out a fixing bolt and remove from a cranked shaft a cogwheel of a drive of GRM, - in case of need use a stripper intended for dismantle of a steering wheel. Take from a groove in a pin of a cranked shaft a segment shponka. Having used a knife with a thin flexible edge, cut through a face surface of an epiploon.
    Having hooked the wrapped-up soft rags a screw-driver, take an epiploon from the landing nest in the case of the oil pump (1).
    Remove assembly of the oil pump (see. The section Removal, installation and service of the oil pump) and manually fill a new epiploon in a landing nest in its case.
    By means of a press and a suitable opravka plant an epiploon in a nest aflush with a surface of the case of the pump, - rest an opravka only against a firm face surface of an epiploon.
    Further installation is made as it should be, the return to an order of dismantle of components. Do not forget about need of observance of requirements of Specifications of Head the Engine to efforts of a tightening of carving fixture. Fill in in the engine fresh engine oil. Start the engine and check tightness of landing of an epiploon. In summary check correctness of installation of a corner of an advancing of ignition (see. The head of System of electric equipment of the engine), in case of need make necessary corrections (correct landing of a belt of a drive of GRM, having tracked correctness of combination of adjusting labels, - see. Head Current leaving and service).

Back epiploon

 PERFORMANCE ORDER

    Disconnect a negative wire from the battery. Hang out the car over the earth. Remove transmission (see. Head Five-step manual box of gear shifting or Automatic transmission). On models from RKPP remove coupling assembly (see. Head Transmission line). By means of the special adaptation block a flywheel / a driving disk from a provorachivaniye (see an illustration) Turn out six fixing bolts and remove a flywheel / a driving disk. Turn out six fixing bolts and remove a back cover of the engine.
    Having hooked a suitable screw-driver, take an old epiploon from the landing nest.
    Estimate a condition of a gear wreath of a flywheel / a driving disk and coupling components (model with RKPP). Replace defective components. Slightly grease sealing edges of the NEW epiploon and a wall of a landing nest in a back cover of the engine with pure impellent oil.
    Accurately fill an epiploon (1) in a nest of a cover (2).
    By means of a press and a suitable opravka plant an epiploon in a nest aflush with a cover surface, - rest an opravka only against a firm face surface of an epiploon.
    Establish into place a back cover and fix it bolts. Establish a flywheel / a driving disk. Having greased a carving part previously the smoothed-out fixing bolts with hermetic, fix them a flywheel / a driving disk, having blocked it from a provorachivaniye by means of the special adaptation (see an illustration), - bolts are tightened in three stages with strict observance of requirements of Specifications of Head the Engine.

The carving part of fixing bolts should be completely cleared of old hermetic, - if to achieve absolute cleaning it is not possible, it is necessary to replace the corresponding bolt.

    Further installation is made as it should be, the return to an order of dismantle of components. Do not forget about need of observance of requirements of Specifications of Head the Engine to efforts of a tightening of carving fixture. Fill in in the engine fresh engine oil. Start the engine and check tightness of landing of an epiploon.